www.fairchildsemi.com rev. 2.0 6/2/02 features all-cmos design in sot-23 or sc70 package a grade ?% precision in reset detection standard grade : ?% precision in reset detection only 1? of iq over 2ma of sink current capability built-in hysteresis of 5% of detection voltage voltage options of 2.6, 2.7, 2.8, 2.9, 3.1, 4.4, and 4.6v ? most supervisory applications active low push-pull output applications microprocessor reset circuits memory battery back-up circuitry power-on reset circuits portable and battery powered electronics description all-cmos voltage monitoring circuit in either a 3-lead sot-23 or sc70 package offers the best performance in power consumption and accuracy. the ilc5062 is available in a series of ?% (a-grade) or 2% (standard grade) accurate trip voltages to ? most micropro- cessor applications. even though its output can sink over 2ma, the device draws only 1? in normal operation. additionally, a built-in hysteresis of 5% of detect voltage simpli?s system design. v ref v in v ss v out complementary cmos output pin-package con?urations block diagram v in top view v ss v out 2 1 3 v in v ss v out 2 1 3 sc-70 sot-23 ilc5062 sot-23 power supply reset monitor with 1% precision
rev. 1.9 6/2/02 2 product specification ilc5062 absolute maximum ratings electrical characterisitcs ilc5062 (t a =25?c) note: an additional resistor between the v in pin and supply voltage may cause deterioration of the characteristics due to increasing of v dr . parameter symbol ratings units input voltage v in 12 v output current i out 50 ma output voltage v out v ss -0.3~v in =+0.3 v continuous total power dissipation (sot-23) p d 150 mw operating ambient temperature t opr -30~+80 ?c storage temperature t stg -40~+125 ?c parameter symbol conditions min. typ. max. units detect fail voltage v df a grade v df x 0.99 v df v df x 1.01 v detect fail voltage v df standard grade v df x 0.98 v df v df x 1.02 v hysteresis range v hys v df x 0.02 v df x 0.05 v df x 0.08 v supply current i ss v in = 1.5v v in = 2.0v v in = 3.0v v in = 4.0v v in = 5.0v 0.9 1.0 1.3 1.6 2.0 2.6 3.0 3.4 3.8 4.2 ? operating voltage v in v df = 2.1 ~ 6.0v 1.5 10.0 v output current i out n-ch v ds = 0.5v v in = 1.0v v in = 2.0v v in = 3.0v v in = 4.0v v in = 5.0v p-ch v ds = 2.1v v in = 8v 2.2 7.7 10.1 11.5 13.0 -10 ma temperature characteristics ? v df /( ? t opr ? df ) -30?c < topr < 80?c -200 ?00 +200 ppm/?c delay time (release voltage output inversion) t dly (v dr to v out inversion) 0.1 ms
product specification ilc5062 rev. 1.9 6/2/02 3 6 5 4 3 1 2 input voltage (v in ) detect release voltage (v dr ) detect fail voltage (v df ) minimum operating voltage (v min ) ground voltage (v ss ) output voltage (v out ) ground voltage (v ss ) functional description the following designators 1~6 refer to the timing diagram below. 1. while the input voltage (v in ) is higher than the detect voltage (v df ), the output voltage at v out pin equals the input volt- age at v in pin. 2. when the input v in voltage falls lower than v df , v out drops near ground voltage. 3. if the input voltage decreases below the minimum operating voltage (v min ), the v out output voltage will be unde?ed. 4. during an increase of the input voltage from the v ss voltage, v out is unde?ed at the voltage below v min . exceeding the v min level, the ouput stays at the ground level (v ss ) between the minimum operating voltage (v min ) and the detect release voltage (v dr ). 5. if the input voltage increases more than v dr , the output voltage at v out pin equals the input voltage at v in pin. 6. the difference between v dr and v df is the hysteresis in the system.
ilc5062 product specification 4 rev. 1.9 6/2/02 typical performance characteristics - general conditions for all curves 0 12 3 4 ilc5062m-27 supply current vs input voltage supply current i ss (a) input voltage v in (v) 0 1 2 3 4 5 67 8 910 t a = 80 ? c -30 ? c 25 ? c 0 12 3 4 ilc5062m-44 supply current vs input voltage supply current i ss (a) input voltage v in (v) 0 1 2 3 4 t a = 80 ? c 5 67 8 910 25 ? c -30 ? c 0 0.5 1.0 ilc5062m-27 n-ch driver output current vs v ds output current:i out nch (ma) v ds (v) 0 10 20 30 40 v in = 2.5v 2.0v 1.5 2.0 2.5 3.0 1.5v 0 12 ilc5062m-44 n-ch driver output current vs v ds output current:i out nch (ma) v ds (v) 0 20 40 60 80 v in = 4.0v 2.0v 3 4 1.5v 10 30 50 70 2.5v 3.5v 3.0v 0 1 2 ilc5062m-27 v out vs v in output voltage:v out (v) input voltage v in (v) 0 1 2 3 4 3 4 t a = 80 ? c 25 ? c -30 ? c 0 1 2 ilc5062m-44 v out vs v in output voltage:v out (v) input voltage v in (v) 0 1 2 3 4 3 4 56 t a = 80 ? c 5 6 25 ? c -30 ? c
product specification ilc5062 rev. 1.9 6/2/02 5 typical performance characteristics - general conditions for all curves 0 1 2 ilc5062m-27 p_ch driver output current vs input voltage output current:i out pch (ma) input voltage v in (v) 0 2 4 6 3 4 5 1.5v 8 10 678910 1.0v v ds = 2.1v 0.5v 0 1 2 ilc5062m-44 p_ch driver output current vs input voltage output current:ioutpch (ma) input voltage v in (v) 0 2 4 6 3 4 5 8 10 678910 1.0v v ds = 2.1v 0.5v 12 1.5v -40 -20 ilc5062m-27 v dr and v df vs temperature release voltage:v df and release voltage:v dr ambient temperature:t a 2.5 2.6 2.7 2.8 0 20 2.9 3.0 40 60 80 v dr (v) v df (v) 0 0.5 1.0 ilc5062m-27 n-ch driver output current vs input voltage output current:i out nch (ma) input voltage v in (v) 0 5 10 15 1.5 2.0 2.5 3.0 v ds = 0.5v 20 t a = -30 ? c 25 ? c 80 ? c 0 1 2 ilc5062m-44 n-ch driver output current vs input voltage output current:i out nch (ma) input voltage v in (v) 0 5 10 15 3 4 5 20 25 v ds = 0.5v t a = -30 ? c 25 ? c 80 ? c
ilc5062 product specification 6 rev. 1.9 6/2/02 sot-23 0.120 0.105 0.079 0.071 0.004 0.001 0.040 0.031 0.021 0.015 0.055 0.047 0.098 0.083 0.010 0.005 0.0059 0.0035 0-8 ? pkg c l 0.76 0.76 0.95 2.29 land pattern recommendation
rev. 1.9 6/2/02 7 product specification ilc5062 .004 (.10) .026 (.65) .052 (1.3) .087 (2.2) .071 (1.8) .016 (.40) .012 (.30) .043 (1.1) .032 (.80) .018 (.45) .006 (.15) .010 (.25) .004 (.10) .009 (.23) .005 (.13) .087 (2.2) .079 (2.0) .053 (1.35) .045 (1.15) land pattern recommendation 0.65 1.80 0.5 0.6 0.65 sc70
6/2/02 0.0m 001 stock#dsxxxxxxxx ? 2002 fairchild semiconductor corporation life support policy fairchild s products are not authorized for use as critical components in life support devices or systems without the express written approval of the president of fairchild semiconductor corporation. as used herein: 1. life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. a critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com disclaimer fairchild semiconductor reserves the right to make changes without further notice to any products herein to improve reliability, function or design. fairchild does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights, nor the rights of others. ilc5062 product specification note 1: last digit in the "top marking" information (represented by "y" in the above table) represents internal assembly lot number note 2: orientation of tape & reeled devices is right. ordering information part top reset output package packing number marking threshold (v) type method ilc5062am23 c3ay 2.3 1% push-pull, active low 3-pin, sot23 3000 units in t&r ilc5062am25 c5ay 2.5 1% push-pull, active low 3-pin, sot23 3000 units in t&r ilc5062am26 c6ay 2.6 1% push-pull, active low 3-pin, sot23 3000 units in t&r ilc5062am27 c7ay 2.7 1% push-pull, active low 3-pin, sot23 3000 units in t&r ilc5062am28 c8ay 2.8 1% push-pull, active low 3-pin, sot23 3000 units in t&r ilc5062am29 c9ay 2.9 1% push-pull, active low 3-pin, sot23 3000 units in t&r ilc5062am30 d0ay 3.0 1% push-pull, active low 3-pin, sot23 3000 units in t&r ilc5062am31 d1ay 3.1 1% push-pull, active low 3-pin, sot23 3000 units in t&r ilc5062am37 d7ay 3.7 1% push-pull, active low 3-pin, sot23 3000 units in t&r ilc5062am44 e4ay 4.4 1% push-pull, active low 3-pin, sot23 3000 units in t&r ilc5062am46 e6ay 4.6 1% push-pull, active low 3-pin, sot23 3000 units in t&r ilc5062m23 c3y 2.3 2% push-pull, active low 3-pin, sot23 3000 units in t&r ilc5062m25 c5y 2.5 2% push-pull, active low 3-pin, sot23 3000 units in t&r ilc5062m26 c6y 2.6 2% push-pull, active low 3-pin, sot23 3000 units in t&r ilc5062m27 c7y 2.7 2% push-pull, active low 3-pin, sot23 3000 units in t&r ilc5062m28 c8y 2.8 2% push-pull, active low 3-pin, sot23 3000 units in t&r ilc5062m29 c9y 2.9 2% push-pull, active low 3-pin, sot23 3000 units in t&r ilc5062m30 d0y 3.0 1% push-pull, active low 3-pin, sot23 3000 units in t&r ilc5062m31 d1y 3.1 2% push-pull, active low 3-pin, sot23 3000 units in t&r ilc5062m37 d7y 3.7 2% push-pull, active low 3-pin, sot23 3000 units in t&r ilc5062m44 e4y 4.4 2% push-pull, active low 3-pin, sot23 3000 units in t&r ilc5062m46 e6y 4.6 2% push-pull, active low 3-pin, sot23 3000 units in t&r ilc5062aic23 c3ay 2.3 1% push-pull, active low 3-pin, sc70 3000 units in t&r ilc5062aic25 c5ay 2.5 1% push-pull, active low 3-pin, sc70 3000 units in t&r ilc5062aic26 c6ay 2.6 1% push-pull, active low 3-pin, sc70 3000 units in t&r ilc5062aic27 c7ay 2.7 1% push-pull, active low 3-pin, sc70 3000 units in t&r ilc5062aic28 c8ay 2.8 1% push-pull, active low 3-pin, sc70 3000 units in t&r ilc5062aic29 c9ay 2.9 1% push-pull, active low 3-pin, sc70 3000 units in t&r ilc5062aic30 d0ay 3.0 1% push-pull, active low 3-pin, sc70 3000 units in t&r ILC5062AIC31 d1ay 3.1 1% push-pull, active low 3-pin, sc70 3000 units in t&r ilc5062aic37 d7ay 3.7 1% push-pull, active low 3-pin, sc70 3000 units in t&r ilc5062aic44 e4ay 4.4 1% push-pull, active low 3-pin, sc70 3000 units in t&r ilc5062aic46 e6ay 4.6 1% push-pull, active low 3-pin, sc70 3000 units in t&r ilc5062ic23 c3y 2.3 2% push-pull, active low 3-pin, sc70 3000 units in t&r ilc5062ic25 c5y 2.5 2% push-pull, active low 3-pin, sc70 3000 units in t&r ilc5062ic26 c6y 2.6 2% push-pull, active low 3-pin, sc70 3000 units in t&r ilc5062ic27 c7y 2.7 2% push-pull, active low 3-pin, sc70 3000 units in t&r ilc5062ic28 c8y 2.8 2% push-pull, active low 3-pin, sc70 3000 units in t&r ilc5062ic29 c9y 2.9 2% push-pull, active low 3-pin, sc70 3000 units in t&r ilc5062ic30 d0y 3.0 1% push-pull, active low 3-pin, sc70 3000 units in t&r ilc5062ic31 d1y 3.1 2% push-pull, active low 3-pin, sc70 3000 units in t&r ilc5062ic37 d7y 3.7 2% push-pull, active low 3-pin, sc70 3000 units in t&r ilc5062ic44 e4y 4.4 2% push-pull, active low 3-pin, sc70 3000 units in t&r ilc5062ic46 e6y 4.6 2% push-pull, active low 3-pin, sc70 3000 units in t&r
|
